I have been so busy with real life, I just haven't had the time to post here in a while.
Here is my last project, I made a Henrician for my husband in September for my October elevation to Pelican.
Everyone is used to seeing him in tunic's and cotehardies.
He looked almost unrecognizable in it. And he loved it!!
I can see in the picture that the outer garment's sleeves slipped down below his elbow. He's a guy, what can I say. He has on black hose, a white shirt, a black and gold trimmed doublet with black chevrons that have been beaded in-between said chevrons and a over gown of chenille trimmed in brown and tan trim and lots of faux fox fur. Oh and he is topped off with a Henrician hat made of black wool and trimmed with ouches and pearls.
Trials and Tribulations of Sewing
Monday, January 26, 2015
Monday, September 9, 2013
Medieval Hose for Women
Virtually everyone wore hose as they were called. They
are seen in nearly every manuscript out there. This is only one possible pattern or way to make hose.
Men wore hose that went up
the inside of the leg to the crotch and on the outside of the hip via a strap
and points (ties) to the waist. Men
could choose to wear the hose tied up or rolled down. A garter was secured either above the knee or
below the knee, the extra fabric was rolled down.
Women’s hose, which we will
be concentrating on today, were worn to either above or below the knee and
secured with a garter.
You will need approximately
1 yard of 54” muslin to make your pattern and the same amount for the actual
hose either of linen or wool fabric.
Measuring:
Below are reasonable renditions of the shape of the pattern pieces (not to scale).
1) Place your
foot on a piece of paper and trace around said foot. If your feet are the same
size, no worries, just flip your cut fashion fabric over for the other foot. Be
sure to trace straight down, keeping
your pencil perpendicular to your leg; do
not angle your pencil. Make a mark on each side of your foot, at the tall part
of your arch. This is where the vamp
will start and end on each side.
2) Measure
over the arch of your foot from side to side, from the high point of the arch
and to the end of the toes. You should
have half of an oblong shaped pattern. This
covers the vamp of the foot.
3) Measure
from the heel base up the back of the leg to the point where you want the top
of your hose to be. And around your
ankle and calf at it’s largest point.
OR:
1) As above.
2) Lay a bit of fabric over the arch of your foot and
trace from side to side and from toe to top of arch.
3) Wrap a bit of muslin around the calf and pin up the
back of the leg. Pin the fabric close. Using a marker, draw your seam line and
the line over the top of the foot where the vamp will be attached. After you
remove the fabric, and lay it flat, add ½ inch to allow for the seam allowance.
See Fig 2 and 3.
Please note that with either way, be sure to cut the leg
portion on the bias, not the grain of the fabric. This allows for a little
stretch in your hose around the calf of your leg.
Your final pattern should
take your hose to just over your knee, for room to roll them down or even
higher if you wish to garter your hose above your knee.
Sewing:
I like to sew the vamp to
the sole first. Pin and trim, then sew. Make sure to match the ends of your vamp
to the marks on the sole. After Fig. 1, It
looks like a little half slipper when you are done.
Carefully pin the arch of
the vamp to the upside curve of the leg.
That is, the part of the fabric between the sides of the heel flaps.
Sew the leg to the vamp
first, then the sides of the leg to the sole, Fig 2. Then sew the back seam last, Fig 3.
Try your hose on, make any
adjustments necessary. For a little more comfort, trim any excess seam
allowance.
Hem your hose at the desired
height and enjoy. Since there is a left
and a right foot made on the hose, I like to add a little “L” or “R” to either
sock. Makes it easier for putting them
on!
Repeat with other leg.
**** Make your first sewn
pair of hose out of muslin, you may need to try several times to get your
pattern just right. Don’t give up.
Garter:
Gartered on |
Rolled over |
Garters could be leather,
ribbon or inkle trim. Buckles and leather (saddle ties) are available from Tandy
Leather in Costa Mesa or you can purchase pre-made period ones online.
Garters that we see on men
are leather and are fastened just below the knee. Ladies garters are fastened below the knee.
A Good fit |
Monday, June 17, 2013
Florentine Dress
We had a theme for Coronation earlier in the month, Venetian. I do not think I'd look good in a Venetian so I went with Florentine. It's still Italy after all, right? So I found a portrait that I liked.
This portrait is Madealena Doni, 1506 by Raphael.
I wanted to do something I'd never done before, sew with silk. So after a trip to the garment district in Los Angeles, I came home with 6 yards of rusty colored silk, a yard of black silk and a yard of a pretty blue on blue brocade for the sleeves.
I had a friend fit me for the bodice and I was off. I cut out two layers of inner fabric, one of canvas and one of heavy cotton and then one of the skin layer fabric and one of the silk.
Now silk should be back lined, that is to have an identical layer of fabric sewn to the silk. So I cut out one more layer of the lining and sewed it to the back of the silk around the edges.
To my two lining layers, I determined where the boning would go down the front. I do not really like rigilene, but used it because this dress curves over the bodice. This style of dress isn't flat down the front like a Tudor. I marked the lining for reference then sewed the rigilene in place, making three lines of stiffing. One up the center and then two that flare out toward the neckline.
It looks funky, but it worked. I then pinned the silk and backing over the exterior of the bodice and hand stitched it down around all edges. I literally folded the silk over the edges and stitched it.
The bodice was complete at this stage, but I needed to add the black guarding. (Guarding=guards the edges.) I cut long strips of the black silk about 3 inches wide. From the outside, I pinned the guarding to the fashion fabric and stitched it down. Then folded it over the edges and stitched it down on the inside of the bodice which
hid the zig zagging.
I worked the center guarding first up the front, around the corner and part way along the neckline. I then added the additional guarding that guards nothing (but looks pretty) up the front and around the neckline. Using the same method that I forgot to take a picture of, I sewed the guarding around the arms eyes.
I let the dress hang for 24 hours before hemming.
The sleeves were cut in two pieces and on a curve with a large elbow. One side of the top of the arms is curved while the other half is flat for the under arm. Both seams of the sleeve are french seams. I attached two little rings to the underside of the sleeve cap on the bodice and two cords to the top of the sleeves to tie them to the bodice.
The below picture was taken at Coronation.
This portrait is Madealena Doni, 1506 by Raphael.
I wanted to do something I'd never done before, sew with silk. So after a trip to the garment district in Los Angeles, I came home with 6 yards of rusty colored silk, a yard of black silk and a yard of a pretty blue on blue brocade for the sleeves.
I had a friend fit me for the bodice and I was off. I cut out two layers of inner fabric, one of canvas and one of heavy cotton and then one of the skin layer fabric and one of the silk.
Now silk should be back lined, that is to have an identical layer of fabric sewn to the silk. So I cut out one more layer of the lining and sewed it to the back of the silk around the edges.
To my two lining layers, I determined where the boning would go down the front. I do not really like rigilene, but used it because this dress curves over the bodice. This style of dress isn't flat down the front like a Tudor. I marked the lining for reference then sewed the rigilene in place, making three lines of stiffing. One up the center and then two that flare out toward the neckline.
From here, I sewed the lining together at the shoulders and the side seams and included the inner layers in the seams. Then sewed the fashion fabric together at the shoulders and side seams. At this point the bodice is unfinished in the arms eyes, front and the bottom. I will admit I got a little confused at this point. I folded the lining over the inner layers and folded it down and zig zagged the edge. This not only sealed the top of the rigilene, but secured the layers together even more.
The bodice was complete at this stage, but I needed to add the black guarding. (Guarding=guards the edges.) I cut long strips of the black silk about 3 inches wide. From the outside, I pinned the guarding to the fashion fabric and stitched it down. Then folded it over the edges and stitched it down on the inside of the bodice which
hid the zig zagging.
I worked the center guarding first up the front, around the corner and part way along the neckline. I then added the additional guarding that guards nothing (but looks pretty) up the front and around the neckline. Using the same method that I forgot to take a picture of, I sewed the guarding around the arms eyes.
The picture to the left looks funny and warped for two reasons. One the bodice isn't laced up all the way tight and second, self portraits of one's chest come out weird.
I marked where the spacing would go for the eyelets and sewed them in. Then I attached these nifty looking jewelry findings over the eyelets and sewed them down. The dress is laced up, across, up, across, up across, etc. And is very difficult to do because the jewelry findings are in the way.
The skirt is also flat lined and is in three sections about 48" in width. The sections were sewn together in a french seam and the skirt is knife pleated. When I was satisfied with the evenness of the pleats, I sewed them down then stitched the lining down to hide all interior seams.
I let the dress hang for 24 hours before hemming.
The sleeves were cut in two pieces and on a curve with a large elbow. One side of the top of the arms is curved while the other half is flat for the under arm. Both seams of the sleeve are french seams. I attached two little rings to the underside of the sleeve cap on the bodice and two cords to the top of the sleeves to tie them to the bodice.
The below picture was taken at Coronation.
Monday, June 3, 2013
Kimono's for Mercy... cause I can't remember her SCA name.
Our dear Mercy was finally asked to become a member of the Order of the Laurel for Pottery. She's probably one of the best potters on the west coast, at least in my opinion.
Her persona is, I think a medieval merchant. So no geisha clothes!! (Get your mind out of the gutter!!)
So to make a kimono is relatively easy, a bunch of rectangles sewn together. Right? Yea, not so much. Especially depending on what kind of fabric you are using. Mercy had some lovely gold with little stripes fabric and some even better burgundy with gold laurel wreaths. And she needed something to wear next to her skin, so I made a white linen kimono too. Because she's a merchant, she wore a Hakama, a divided skirt that resembles a wide pair of trousers that she bought.
I was bad and did not take a lot of pictures. She had a Folkware
Fashion's pattern that I used. It consists of 4 rectangles, two front
and two back, 2 front facing angular pieces, 2 Sleeves and a collar. The black and white picture to the right is from the pattern itself, showing the front and back with 2 sleeve length options.
Her persona is, I think a medieval merchant. So no geisha clothes!! (Get your mind out of the gutter!!)
So to make a kimono is relatively easy, a bunch of rectangles sewn together. Right? Yea, not so much. Especially depending on what kind of fabric you are using. Mercy had some lovely gold with little stripes fabric and some even better burgundy with gold laurel wreaths. And she needed something to wear next to her skin, so I made a white linen kimono too. Because she's a merchant, she wore a Hakama, a divided skirt that resembles a wide pair of trousers that she bought.
I was bad and did not take a lot of pictures. She had a Folkware
Fashion's pattern that I used. It consists of 4 rectangles, two front
and two back, 2 front facing angular pieces, 2 Sleeves and a collar. The black and white picture to the right is from the pattern itself, showing the front and back with 2 sleeve length options.
I started with the gold fabric first, it was some kind of upholstery material I think. Very tough to hand sew. Did I mention just how much hand sewing there is on a kimono? I suppose you could sew the entire thing by machine, but that's not how I roll. I try my best not to have any stitching on the outside of my garments.
All seams were french seams, that is to sew the wrong sides together, then turn the pieces and seal up that inside out seam into a new seam. This makes for a very clean seam on the inside, something reserved for court wear or fancy dress.
I sewed the 2 back pieces together and then sewed the front to back on at the shoulders. And then I sewed the front facing strip on. It is a half size strip with an angular top that disappears below the collar. I hope that made sense.
Next came the collar. Though it is just a long strip that goes around the neck, it needed to be finished by hand. But first I needed to finish the front seams of the facing strip. The gold fabric was very tough and I had to use my leather thimble to protect my finger tip. I don't like metal thimbles. Once the facing was finished, I sewed the collar on and then hand finished it.
For the sleeves, they are a simple short-ish sleeve. The can be either attached to the body for the full length of the sleeve or to leave a little opening, for air flow I suppose. Short in how much they cover the arm and short in length up and down. Since the gold fabric was to be the inner kimono, I made a shorter length sleeve as you can see in the left of the black and white picture. Doing french seams is easy enough but the fabric had a lot of substance to it and for the underarm it was difficult to do.
There are no visible rough seams on the kimono due
to the french and hand sewn seams.
The burgundy kimono is sewn in the same way. But because it had a pattern to it, I did not put in a back seam. The sleeves however, have a shoulder seam to make the pattern face the same direction throughout the entire garment.
The white under kimono is made the same way but I didn't do french seams. It also has a smaller collar because it is only an undergarment and not expected to be seen. I used my overlock machine for the seams and then added another line of stitching for structure.
For the obi or belt. The merchant class wore a narrow belt, about 5 inches wide that ties to one side. The belt center is in the front of the person, wrapped around and tied in the front. We chose a gold silk because it tied the garment together really well. The white under kimono is not visible.
Mercy in her elevation outfit with a bit of white Japanese style makeup on as what would have been done in medieval times.
She looked great.
Sunday, November 18, 2012
Appliqued Banners
Our Barony recently wanted new banners. We knew what we wanted to do and only a few folks had ever sewn a banner. Three gold trees (of fashion fabric) with a laurel wreath, on a blue background with a gold border.
The approximate finished size will be 20” wide by 25” high with 4 tabs for hanging on a cross bar. PLEASE READ THESE IN THEIR ENTIRETY BEFORE STARTING.
After cutting out your designs, iron all of the fabric. Iron a fold in the middle of the large rectangle piece that is to be the background of the front and the backing. This line will be the divider between front and back. (Cut out 2 half trees, 1 full tree, a border, a back, 4 tabs and the wreath.)
Take your gold border fabric and trim it to a 2" wide strip. If one strip isn't enough to go around your background piece, add another strip to it and after sewing, iron the seam flat.
Using Stitch Witchery or some other iron on backing, iron a piece onto
the green that you will be using for your laurel wreath. On the
remaining paper backing, trace your laurel wreath pattern on paper.
This will be the back of your wreath. Carefully, cut out the wreath and
then iron it to the center tree. By doing it in this order, you should
have a clean and sturdy edge.
Place your wreath in the center tree and remove the paper
backing. Make sure it is nice and even before you iron it in
place. Iron according to instructions, usually 5-8 seconds,
then set the trees aside.
Taking the border fabric, line it up on your background piece and if you have a seam, place it near a lower corner. I like to sew the backing and border right sides together. This way when it is turned and ironed, you have a nice front bottom edge of the banner, and 1 seam is completed. Pin the heck out of your border to keep it flat and in the right place.
To make the corner pleats, line up the edge of your border and backing. Pin in place before and after your pleat. Slowly tuck in the excess fabric until you have a square inside corner, pin and then sew in place.
On a scrap of fabric, play
with your zigzag stitch and make it tight/close together and wide. Sew the
inside of the border down using your setting. Sew from the bottom, to the top
on each side; left and up and right and up. This helps prevent wrinkles and
puckers. Make sure that most of the stitch is on your border fabric and the
opposite edge of your stitch just past the edge of the border fabric. This will help your border from fraying.
Once you are at your border ends, wherever they may fall, pin a seam into the ends, sew, trim and iron flat. Finish with your tight zig zag stitch.
Line up your trees in the center of the banner, inside the border. The trees should not touch the border fabric. Again pin the heck out of your trees, they have an amazing tendency to creep across your fabric and could be crooked. I like to sew from the top to the bottom here. Place your two back trees down and the center tree over them.
I sew down one side, from the top of the center tree to the bottom, then do the same on the other side. This helps prevent unwanted puckers. The outside trees are similar. Sew from the top to the bottom, then the other side of the trunk and root. Then do the third tree the same.
From here, you are ready to finish the wreath in the trees. Using a regular but narrow zig zag stitch, sew down along the edge of the wreath. This makes a permanaite attachment of the wreath to the trees and to the backing fabric!
The banner is finished except for the edges and tabs at this point.
And one last note: This isn't the only way to do a banner!
The approximate finished size will be 20” wide by 25” high with 4 tabs for hanging on a cross bar. PLEASE READ THESE IN THEIR ENTIRETY BEFORE STARTING.
After cutting out your designs, iron all of the fabric. Iron a fold in the middle of the large rectangle piece that is to be the background of the front and the backing. This line will be the divider between front and back. (Cut out 2 half trees, 1 full tree, a border, a back, 4 tabs and the wreath.)
Take your gold border fabric and trim it to a 2" wide strip. If one strip isn't enough to go around your background piece, add another strip to it and after sewing, iron the seam flat.
Using Stitch Witchery or some other iron on backing, iron a piece onto
the green that you will be using for your laurel wreath. On the
remaining paper backing, trace your laurel wreath pattern on paper.
This will be the back of your wreath. Carefully, cut out the wreath and
then iron it to the center tree. By doing it in this order, you should
have a clean and sturdy edge.
Place your wreath in the center tree and remove the paper
backing. Make sure it is nice and even before you iron it in
place. Iron according to instructions, usually 5-8 seconds,
then set the trees aside.
Taking the border fabric, line it up on your background piece and if you have a seam, place it near a lower corner. I like to sew the backing and border right sides together. This way when it is turned and ironed, you have a nice front bottom edge of the banner, and 1 seam is completed. Pin the heck out of your border to keep it flat and in the right place.
To make the corner pleats, line up the edge of your border and backing. Pin in place before and after your pleat. Slowly tuck in the excess fabric until you have a square inside corner, pin and then sew in place.
begin fold |
tuck it in |
pin it down |
sew in place |
Once you are at your border ends, wherever they may fall, pin a seam into the ends, sew, trim and iron flat. Finish with your tight zig zag stitch.
Line up your trees in the center of the banner, inside the border. The trees should not touch the border fabric. Again pin the heck out of your trees, they have an amazing tendency to creep across your fabric and could be crooked. I like to sew from the top to the bottom here. Place your two back trees down and the center tree over them.
I sew down one side, from the top of the center tree to the bottom, then do the same on the other side. This helps prevent unwanted puckers. The outside trees are similar. Sew from the top to the bottom, then the other side of the trunk and root. Then do the third tree the same.
The banner is finished except for the edges and tabs at this point.
Iron
the trees using a ironing cloth. (I like an old scrap of white cotton). Using a
3-1 ratio of water and white vinegar. Dip your cloth and lay over the trees.
Iron until the cloth is dry. (I don’t know why, but using the vinegar solution
helps the ironing, whether flat or a fold, stay.) Your banner front is almost
complete at this point.
Turn your banner in half at your earlier ironed fold which is now the bottom of the
banner. Pin your banner, front to back along the sides. Using a long stitch,
sew/baste up the sides of your banner to the top, but not along the top. Fold
the banner inside out and check your border width. You should have about a 2”
border. Make any adjustments and if it looks good, turn your banner again with
the wrong side out and re-stitch using a normal length stitch. Iron flat making
sure the back does not show around the edges past your gold border. Iron your
top edges, matching the width of the rest of the border.
For
the tabs, sew a single seam along the long edges then iron them flat; placing
the seams on what will be the inside of the fold. Pin your tabs to the banner,
spacing them evenly out. Pin the back to the front with the tabs stuck down
between the sides. Make sure the banner hangs even. Sew either by hand or
machine carefully along the top edge, sealing the banner shut.
WaLa... you are done. Hopefully you will have a banner that is pleasing to the eye. Remember they don't have to be perfect. Step 5 feet back and most errors disappear!
Subscribe to:
Posts (Atom)